fbpx
MSS SP-44 Flange Specification

MSS SP-44

MSS SP-44 refers to the steel pipeline flanges specifications covers pressure-temperature ratings, materials, dimensions, tolerances and testings. Material Grades from F36, F42, F46, F48, F50, F52, F56, F60, F65, F70, F80, which names from yield strength by 36 ksi (F36) to 80 ksi (F80).

The standard inlcudes all the flange types in forged steel or steel inlcudes Weld Neck Flange, Slip On Flange, Lap Joint Flange and Blind flanges and etc.

Dimensional and tolerance requirements for NPS 10 and smaller flanges in this standard refer to ASME B16.5. 

Pressure Temperature Ratings

Flanges understand the standard has follwing pressure ratings: Class 150, 300, 400, 600 or 900.

NPSDNNPSDN
1230038950
14350401000
16400421050
18450441100
20500461150
22550481200
24600501250
26650521300
28700541350
30750561400
32800581450
34850601500
36900

Materials of MSS SP-44

All materials used for making MSS SP-44 flanges shall be “killed” steel. It shall be suitable for field welding to other flanges, fittings, or pipe manufactured according to ASTM A105, A53, A106, A350, A381, A516, A537, A694, A707 and API 5L.

It defines maximum carbon content of 0.30%, and CE shall not exceed 0.48%, based on ladle analysis, without prior approval of the purchaser. If the CE exceeds 0.45%, the flange shal be marked with actual CE result. All test methods shall be as specified in ASTM A370.

Chemical Composition of MSS SP-44

Elemen​​​​​tLimits (%)
Min.Max.
C-0.3
Mn0.61.6
P-0.025
S-0.025
Si0.150.35
Cu-0.4
Ni-0.4
Cr-0.3
Mo-0.12
V-0.11
Nb-0.05
B-0.001
Cu+Ni+Cr+Mo-1

Tensile Requirements of MSS SP-44

SI (Metric) and U.S. Customary
GradeYield Point
(Min.)
Tensile Strength
(Min.)
Elongation 50mm 
MpaksiMpaksi(2 in.) (Min. %)
F36248364146020
F42290424146020
F46317464146020
F48331484276220
F50345504416420
F52359524556620
F56386564696820
F60414605177520
F65448655317718
F70483705528018
F80550806209016

Impact Test

Impact testing is not required for Grade F42 and lower. 

From each steel sheet, one set (three specimens) shall be tested at a maximum temperature of -45℃ (-50℉) and show 27J (20ft-lb) minimum average, 20J (15 ft-lb) individual minium.

Hardness

Hardness shall be HBW 235 as maximum.

Bolting

Boltings listed in Table 3 shall be used in flanged joints covered by MSS SP-44. Bolting produced from other materials may be used if permitted by the applicable code or governmental regulation. 

Heat Treatment

MSS SP-42 F42 and higher grades shall be normalized, normalized and tempered, quenched and tempered, or precipitation treated and aged. Class 400 and higher classes of Grade F36 flanges shall be anneald, normalized, normalized and tempered, or quenched and tempered as defined in ASTM A961; But the minimum tempering temperature shall be 540℃ (1000℉).

MSS SP-44 Flange Design Spec

MSS SP-44 Flange Design Spec

Drilling template

The flange drilling template is determined as follows:

The Class 150 flange drilling template is identical to the Class 125 in ASME B16.5 and ASME B16.1.

The drilled template for class 300 flanges smaller than or equal to NPS24 is the same as that for class 250 flanges in ASME B16.5 and ASME B16.1. The drilled templates for class 400, class 600, and class 900 flanges in sizes less than or equal to NPS24 are the same as those for ASME B16.5.

The NPS 26 through NPS 60 Class 150, 300, 400, 600, and 900 flanges are the same as those of series A flanges in ASME standard B16.47.

Flange Ring design

For flanges with nominal pipe diameter less than or equal to NPS24, the outer diameter and flange thickness shall meet the requirements of ASME B16.5. For flanges with nominal pipe diameters of NPS26 through NPS60, the outer diameter and flange thickness shall comply with the requirements of ASME B16.47 for series A flanges

Hub Design

ASME B16.5 and B16.47 weld flange ratings are based on the weld flange neck and have a calculated wall thickness at least equal to the pipe. The pipe has a specified minimum yield strength of 276 MPa (40000 psi) and a maximum bore size.

NPS 60 and Smaller

When the mechanical properties (minimum yield strength) of the various parts are equal to or greater than the line to which it is connected, the flange neck may be the same size as specified in the ASME B16.5 or 16.47A series.

Marking

Flanges shall be marked in accordance with the rules specified in MSS Standard Practice SP-25. In addition, the letter PL should be added before the level symbol. The grade symbol on the weld neck flange marks the material grade of the weld flange neck.

Facing

The accuracy of the pipe flange contact surface should be determined by the visual comparison method using the Ra sample block instead of the stylus plotter and the electronic magnifier.

Raised Face

It provide concentric serrated or helical teeth with an accuracy between 3.2 μm (125 μinch) and 6.3μm (250μinch). The cutting tool used shall have a radius greater than or equal to 1.5mm (0.06 in) and 1.7 to 2.2 grooves per mm (44 to 55 grooves per inch).

Ring Joint

The side surface roughness of gasket groove shall not exceed 1.6μm (63μinch).

Flange Testing

Hydrostatic test of the flange is not required. However, the hydrostatic pressure test of the flange joint may be carried out at a pressure not exceeding 1.5 times the 38 ° C (100 ° F) rating.

What is MSS SP 44 flange?

MSS SP-44-2019 covers pressure-temperature ratings, materials, dimensions, tolerances, marking, and testing for steel pipeline flanges. The welding neck type flanges shall be forged steel, and the blind flanges may be made from either forged steel or from steel plate.